How to remove gas tank on 1988 Honda CBR 1000?
Q. I need to check the radiator bacause my bike is overheating but I need to remove the gas tank first. I couldn't see any obvious way to do this. Any help would be greatly appreciated.
Asked by Jim - Sun Jun 1 23:15:56 2008 - - 2 Answers - 0 Comments
A. remove seat,, remove tank bolt.. lift rear of tank & rmove carbie tubes.. slide tank rearwards & up... or you could go here & download the free manual... or here
Answered by easygoing157 - Mon Jun 2 00:01:28 2008
Q. I need to check the radiator bacause my bike is overheating but I need to remove the gas tank first. I couldn't see any obvious way to do this. Any help would be greatly appreciated.
Asked by Jim - Sun Jun 1 23:15:56 2008 - - 2 Answers - 0 Comments
A. remove seat,, remove tank bolt.. lift rear of tank & rmove carbie tubes.. slide tank rearwards & up... or you could go here & download the free manual... or here
Answered by easygoing157 - Mon Jun 2 00:01:28 2008
How to remove gas or fuel tank for a 1998 Yamaha V-Max?
Q. The gas tank is rusty on the inside. Needs to be removed for cleaning.
Asked by Luna - Sun Jun 14 15:36:49 2009 - - 1 Answers - 0 Comments
A. First remove hose and let drain in a recipient. I believe the tank is held by 12mm bolts. The rust will be back.
Answered by Gear M - Tue Jun 16 03:10:12 2009
Q. The gas tank is rusty on the inside. Needs to be removed for cleaning.
Asked by Luna - Sun Jun 14 15:36:49 2009 - - 1 Answers - 0 Comments
A. First remove hose and let drain in a recipient. I believe the tank is held by 12mm bolts. The rust will be back.
Answered by Gear M - Tue Jun 16 03:10:12 2009
How do i remove my gas tank from an 2003 Ford F350?
Q. We put regular gas instead of diesel and now we need to remove it to empty it out.
Asked by Salina B - Tue Dec 4 13:16:09 2007 - - 5 Answers - 0 Comments
A. i don't think you have to remove the tank all the way. disconnect the filler hose and use a length of hose to siphon out the contaminated fuel. if you do have to remove the whole tank, disconnect all hoses and wiring, place a jack under the tank. remove the straps and lower using the jack. install in reverse order.
Answered by freakboynv2000 - Tue Dec 4 13:22:28 2007
Q. We put regular gas instead of diesel and now we need to remove it to empty it out.
Asked by Salina B - Tue Dec 4 13:16:09 2007 - - 5 Answers - 0 Comments
A. i don't think you have to remove the tank all the way. disconnect the filler hose and use a length of hose to siphon out the contaminated fuel. if you do have to remove the whole tank, disconnect all hoses and wiring, place a jack under the tank. remove the straps and lower using the jack. install in reverse order.
Answered by freakboynv2000 - Tue Dec 4 13:22:28 2007
How do you remove the gas tank on a Honda Passport seventy cc scooter?
Q. My father and I have an 1981 model Honda Passport 70 with a very rusted fuel tank which we want to treat with Kreme, however we cannot figure out how to get the fuel tank out of the body of the scooter. We have to take the tank out because it has holes in in the bottom.
Asked by Zephyr - Mon May 11 21:42:49 2009 - - 1 Answers - 0 Comments
A. you pull the lid off, 2 phillips screws on top, you disconect both fuel lines. as you pull up on the fuel tank you tip it slightly forward. it is a tight fit. Then you buy a new tank, Kreme is a nice product but, it chips around the filler neck and the fuel lines.. also a used in good condition tank costs as much as your kreme kit.
Answered by unknown - Mon May 11 21:56:40 2009
Q. My father and I have an 1981 model Honda Passport 70 with a very rusted fuel tank which we want to treat with Kreme, however we cannot figure out how to get the fuel tank out of the body of the scooter. We have to take the tank out because it has holes in in the bottom.
Asked by Zephyr - Mon May 11 21:42:49 2009 - - 1 Answers - 0 Comments
A. you pull the lid off, 2 phillips screws on top, you disconect both fuel lines. as you pull up on the fuel tank you tip it slightly forward. it is a tight fit. Then you buy a new tank, Kreme is a nice product but, it chips around the filler neck and the fuel lines.. also a used in good condition tank costs as much as your kreme kit.
Answered by unknown - Mon May 11 21:56:40 2009
How do I remove the gas tank on a 1994 toyota corolla?
Q. Rails are unbolted, but there are bolts way underneath the car I cannot get to.
Asked by Derek R - Mon Jul 7 14:44:27 2008 - - 1 Answers - 0 Comments
A. untie the knot
Answered by Mr. Singh - Mon Jul 7 14:51:31 2008
Q. Rails are unbolted, but there are bolts way underneath the car I cannot get to.
Asked by Derek R - Mon Jul 7 14:44:27 2008 - - 1 Answers - 0 Comments
A. untie the knot
Answered by Mr. Singh - Mon Jul 7 14:51:31 2008
how do i remove a gas tank?? 1969 plymouth satellite ?
Q. how do i remove a gas tank?and also im taking it out b/c my car 4 some reason on my dashboard it says that im full on gas always and it is not accurate ..whats the thing called that is inside the gas tank that tells how much gas is there?
Asked by i play soccer - Sat Jan 19 17:23:13 2008 - - 2 Answers - 0 Comments
A. the item inside the tank is called the fuel sending unit, removing the tank on a b body mopar is not hard the tank is held to the underside by two straps I had a 69 charger around my filler neck were three bolts if you have that style of filler neck remove those bolts first be sure to support your tank with a floor jack before removing the straps also try to have as little gas in the tank as possible to make the job easier when you lower the tank you will see the lines connected to the sending unit mark the wires and fuel lines for proper reinstall before removal. if your tank was like mine it was full of rust, Eastwood manufacturing company sells a tank refurbishing kit if you need one.
Answered by olddodgenut - Sat Jan 19 17:45:41 2008
Q. how do i remove a gas tank?and also im taking it out b/c my car 4 some reason on my dashboard it says that im full on gas always and it is not accurate ..whats the thing called that is inside the gas tank that tells how much gas is there?
Asked by i play soccer - Sat Jan 19 17:23:13 2008 - - 2 Answers - 0 Comments
A. the item inside the tank is called the fuel sending unit, removing the tank on a b body mopar is not hard the tank is held to the underside by two straps I had a 69 charger around my filler neck were three bolts if you have that style of filler neck remove those bolts first be sure to support your tank with a floor jack before removing the straps also try to have as little gas in the tank as possible to make the job easier when you lower the tank you will see the lines connected to the sending unit mark the wires and fuel lines for proper reinstall before removal. if your tank was like mine it was full of rust, Eastwood manufacturing company sells a tank refurbishing kit if you need one.
Answered by olddodgenut - Sat Jan 19 17:45:41 2008
How to remove gas tank door on a cavalier '96 2 doors?
Q. How to remove gas tank door on a cavalier '96 2 doors?
Asked by cavalier 96 - Wed Nov 15 13:28:44 2006 - - 1 Answers - 0 Comments
A. Drain the tank. Disconnect the negative battery terminal. Now put it up on the lift so your can get under it, and disconnect all the fuel lines going to the tank. There will be more than one, perhaps 2 or 3, fuel, return and vent lines. Unplug the electric wires. Now put your jack in place and remove the bolts holding the straps in place. Once the straps are off, the tank will be free, Lower the jack. You may have to move the tank forward or back to get it free. Installation is the reverse of taking it out.
Answered by oklatom - Wed Nov 15 13:37:38 2006
Q. How to remove gas tank door on a cavalier '96 2 doors?
Asked by cavalier 96 - Wed Nov 15 13:28:44 2006 - - 1 Answers - 0 Comments
A. Drain the tank. Disconnect the negative battery terminal. Now put it up on the lift so your can get under it, and disconnect all the fuel lines going to the tank. There will be more than one, perhaps 2 or 3, fuel, return and vent lines. Unplug the electric wires. Now put your jack in place and remove the bolts holding the straps in place. Once the straps are off, the tank will be free, Lower the jack. You may have to move the tank forward or back to get it free. Installation is the reverse of taking it out.
Answered by oklatom - Wed Nov 15 13:37:38 2006
Is it difficult to remove the gas tank from a 2002 Honda VTX 1800 Motorcycle?
Q. Is it difficult to remove the gas tank from a 2002 Honda VTX 1800 Motorcycle?
Asked by dahlenpt - Fri Jun 6 17:38:43 2008 - - 2 Answers - 0 Comments
A. If you know how to use tools, then it's not that difficult. Honda - 2002 - VTX1800C Seat - remove the two allen bolts #8 and remove the seat. Fuel Tank - unplug the fuel pump wire (fuel pump #2 - 2 prong connector at picture 25 - the wire is at the rear of the tank - take note as to how it's routed so the seat won't pinch it). Remove bolt #28 Remove rubber grommets #11 and store in a safe place (so you don't lose them). Slide the tank backwards a bit, to unhook it from cushions #18 Lift the front of the tank a bit and slide it forward, to rest on the cushions. Reinstall bolt #28 (do not tighten it) through tank and mounting bracket (it will be used as a pivot to lift the tank up). Lift the front of the tank and unplug hose #15 from the… [cont.]
Answered by guardrailjim - Fri Jun 6 19:00:23 2008
Q. Is it difficult to remove the gas tank from a 2002 Honda VTX 1800 Motorcycle?
Asked by dahlenpt - Fri Jun 6 17:38:43 2008 - - 2 Answers - 0 Comments
A. If you know how to use tools, then it's not that difficult. Honda - 2002 - VTX1800C Seat - remove the two allen bolts #8 and remove the seat. Fuel Tank - unplug the fuel pump wire (fuel pump #2 - 2 prong connector at picture 25 - the wire is at the rear of the tank - take note as to how it's routed so the seat won't pinch it). Remove bolt #28 Remove rubber grommets #11 and store in a safe place (so you don't lose them). Slide the tank backwards a bit, to unhook it from cushions #18 Lift the front of the tank a bit and slide it forward, to rest on the cushions. Reinstall bolt #28 (do not tighten it) through tank and mounting bracket (it will be used as a pivot to lift the tank up). Lift the front of the tank and unplug hose #15 from the… [cont.]
Answered by guardrailjim - Fri Jun 6 19:00:23 2008
what do i pour in a gas tank to remove trash?
Q. i know there is something you can pour in the tank and remove the trash but what is it called?
Asked by sexy_hot_gay_dude - Tue Jun 6 22:02:31 2006 - - 3 Answers - 0 Comments
A. Not sure if you mean a gas tank needs to have sediment and so on removed. You need to pull the tank and gas lines and take them to a radiator shop. The can flush the tank and coat it to prevent rust. Just call around and ask if the flush gas tanks and gas lines.
Answered by sanbio - Wed Jun 7 00:16:11 2006
Q. i know there is something you can pour in the tank and remove the trash but what is it called?
Asked by sexy_hot_gay_dude - Tue Jun 6 22:02:31 2006 - - 3 Answers - 0 Comments
A. Not sure if you mean a gas tank needs to have sediment and so on removed. You need to pull the tank and gas lines and take them to a radiator shop. The can flush the tank and coat it to prevent rust. Just call around and ask if the flush gas tanks and gas lines.
Answered by sanbio - Wed Jun 7 00:16:11 2006
How do I remove the gas tank on a 94 jetta?
Q. How do I remove the gas tank on a 94 jetta?
Asked by David J - Wed Mar 5 09:56:15 2008 - - 1 Answers - 0 Comments
A. First, disconect the battery! You don't want an inadvertant spark to light up the fuel. Remove the rubber lines going into the top of the tank, unplug the fuel level sending unti wires. You should see some bolts along the edge of the tank... Oh, BTW is the tank empty. They can be quite diffuclt to handle if they are not. May I ask why you are removing it? Eric
Answered by kravdraa - Wed Mar 5 10:01:27 2008
Q. How do I remove the gas tank on a 94 jetta?
Asked by David J - Wed Mar 5 09:56:15 2008 - - 1 Answers - 0 Comments
A. First, disconect the battery! You don't want an inadvertant spark to light up the fuel. Remove the rubber lines going into the top of the tank, unplug the fuel level sending unti wires. You should see some bolts along the edge of the tank... Oh, BTW is the tank empty. They can be quite diffuclt to handle if they are not. May I ask why you are removing it? Eric
Answered by kravdraa - Wed Mar 5 10:01:27 2008
If you put a motorcycles gas tank filled with water in a freezer to remove a dent, will the tank explode?
Q. Ive been searching around on how to remove a dent in a motorcycle gas tank. One answer that i found is that you can just fill the tank with water and put it in the freezer and as the water freezes it will expand causing it to push out a dent. But my question is will it expand so much as to explode the tank. or misshape it? If anybody has any other suggestions to remove a dent that wont cost alot of money please let me know. Thanks
Asked by Fyre360 - Fri Feb 22 10:43:46 2008 - - 15 Answers - 0 Comments
A. The problem is that the freezing ice pushes out in all directions equally thereby expanding the entire tank just like blowing up a balloon. The whole tank will be distorted and most likely your dent will still be there. I tried this approach with air pressure many years ago and ruined a tank. If the dent is small it is better to fill it with body filler, or if you can access it through the filler neck, you might be able to use a pry bar to push the dent out. (Be careful not to damage the rim of the fill or the gas cap wont seal anymore) As far as some miracle cure for a dent that will simply make it disappear, there are none. (Regardless of what you see on TV)
Answered by hugo21813@verizon.net - Fri Feb 22 13:10:20 2008
Q. Ive been searching around on how to remove a dent in a motorcycle gas tank. One answer that i found is that you can just fill the tank with water and put it in the freezer and as the water freezes it will expand causing it to push out a dent. But my question is will it expand so much as to explode the tank. or misshape it? If anybody has any other suggestions to remove a dent that wont cost alot of money please let me know. Thanks
Asked by Fyre360 - Fri Feb 22 10:43:46 2008 - - 15 Answers - 0 Comments
A. The problem is that the freezing ice pushes out in all directions equally thereby expanding the entire tank just like blowing up a balloon. The whole tank will be distorted and most likely your dent will still be there. I tried this approach with air pressure many years ago and ruined a tank. If the dent is small it is better to fill it with body filler, or if you can access it through the filler neck, you might be able to use a pry bar to push the dent out. (Be careful not to damage the rim of the fill or the gas cap wont seal anymore) As far as some miracle cure for a dent that will simply make it disappear, there are none. (Regardless of what you see on TV)
Answered by hugo21813@verizon.net - Fri Feb 22 13:10:20 2008
My car won't start after I get gas or remove the gas tank cap.?
Q. When I get gas. The car will stall out if left running. If I turn it off the gas pedal will need to be pumped at least 10 times to get it to start. Then I have to rev it up for 20 to 30 seconds and then it runs fine till the next fill up. If you just crank and don't pump it will never start! whats wrong?
Asked by b k - Wed Jun 4 16:48:29 2008 - - 3 Answers - 0 Comments
A. Well 1st off we need to know what year, make, engine etc to draw reference from but Id say you have a plugged or damaged charchole canister. they are usually in the fenderwell area drivers side. they hane lines run from the engine to the canister and then to the tank. have you changed Gas caps recently or anything? any changes since that problem started that you can think of? If I can be of further assistance to you contact me at my free web site www.mycarandineedhelp.com
Answered by CARL G H - Wed Jun 4 17:01:13 2008
Q. When I get gas. The car will stall out if left running. If I turn it off the gas pedal will need to be pumped at least 10 times to get it to start. Then I have to rev it up for 20 to 30 seconds and then it runs fine till the next fill up. If you just crank and don't pump it will never start! whats wrong?
Asked by b k - Wed Jun 4 16:48:29 2008 - - 3 Answers - 0 Comments
A. Well 1st off we need to know what year, make, engine etc to draw reference from but Id say you have a plugged or damaged charchole canister. they are usually in the fenderwell area drivers side. they hane lines run from the engine to the canister and then to the tank. have you changed Gas caps recently or anything? any changes since that problem started that you can think of? If I can be of further assistance to you contact me at my free web site www.mycarandineedhelp.com
Answered by CARL G H - Wed Jun 4 17:01:13 2008
The best way to remove factory sticker from Gas Tank?
Q. Hubby just got a new Honda VTX 1800 and it has that ugly "Warning" sticker right smack dab in the middle of the tank. What would be a good product to remove it without damaging the paint or finish? We've heard everything from a heat gun to wd-40. His last bike the sticker was already removed. Thank you for any suggestions. I thought the heat would damage the finish that's why I was skeptical.
Asked by libralea75 - Fri Jun 16 20:14:17 2006 - - 8 Answers - 0 Comments
A. Living in Florida, the absolute best and easiest way I've found is to just park my bike in the sun for about 15 minutes. The decals can be peeled right off, leaving no residue. I've done the hair dryer method, as well as using products like Goo Gone, etc. Both methods left a ton of residue and were way more work.
Answered by crx81 - Sat Jun 17 06:16:48 2006
Q. Hubby just got a new Honda VTX 1800 and it has that ugly "Warning" sticker right smack dab in the middle of the tank. What would be a good product to remove it without damaging the paint or finish? We've heard everything from a heat gun to wd-40. His last bike the sticker was already removed. Thank you for any suggestions. I thought the heat would damage the finish that's why I was skeptical.
Asked by libralea75 - Fri Jun 16 20:14:17 2006 - - 8 Answers - 0 Comments
A. Living in Florida, the absolute best and easiest way I've found is to just park my bike in the sun for about 15 minutes. The decals can be peeled right off, leaving no residue. I've done the hair dryer method, as well as using products like Goo Gone, etc. Both methods left a ton of residue and were way more work.
Answered by crx81 - Sat Jun 17 06:16:48 2006
Can anyone tell me how to remove rust from a gas tank?
Q. This is a gas tank for a 1984 or 1986 Honda 3-wheeler!
Asked by bikerbabymama - Sun Jun 1 23:33:41 2008 - - 7 Answers - 0 Comments
A. best & cheapest way is the old gravel trick...using new ..small to medium size gravel [ with fairly sharp edge,s]...fill the tank 1/4 full ...shake or vibrate vigorusly...this will remove rust as well as indicate any thin or weak spot,s...be sure to flush the tank thouroly after cleaning...good luck!
Answered by slipstream - Sun Jun 1 23:42:55 2008
Q. This is a gas tank for a 1984 or 1986 Honda 3-wheeler!
Asked by bikerbabymama - Sun Jun 1 23:33:41 2008 - - 7 Answers - 0 Comments
A. best & cheapest way is the old gravel trick...using new ..small to medium size gravel [ with fairly sharp edge,s]...fill the tank 1/4 full ...shake or vibrate vigorusly...this will remove rust as well as indicate any thin or weak spot,s...be sure to flush the tank thouroly after cleaning...good luck!
Answered by slipstream - Sun Jun 1 23:42:55 2008
how to remove gas tank from 03 Jaguar X type?
Q. how to remove gas tank from 03 Jaguar X type?
Asked by Cassandra - Tue Sep 22 13:31:44 2009 - - 2 Answers - 0 Comments
A. pull the bolts out of the straps drop it down disconnect harness and hosses then ther you go
Answered by unknown - Tue Sep 22 14:23:55 2009
Q. how to remove gas tank from 03 Jaguar X type?
Asked by Cassandra - Tue Sep 22 13:31:44 2009 - - 2 Answers - 0 Comments
A. pull the bolts out of the straps drop it down disconnect harness and hosses then ther you go
Answered by unknown - Tue Sep 22 14:23:55 2009
how to remove the gas tank 1997 Dodge Stratus?
Q. the haynes book does not address this car.
Asked by way cool mom - Thu Jun 25 17:50:22 2009 - - 1 Answers - 0 Comments
Q. the haynes book does not address this car.
Asked by way cool mom - Thu Jun 25 17:50:22 2009 - - 1 Answers - 0 Comments
how much water will heet actually remove from the gas tank?
Q. will a simple cup of water casue rough running or stalling or does it take more water to cause my problems? very curious. thanks
Asked by lucky - Sat Mar 17 13:08:04 2007 - - 3 Answers - 0 Comments
A. Water in the gas tank and lines is very common. More so than most people think it is. To help you out here, if you had a two gallon glass container with a gallon of gas in it(doesn't matter what grade), to make it run poorly, you'd have to add about another quart if not nearly a half gallon of water to the gasoline to make it really bad. Rough idling at stop lights/signs as well as stalling is an ignition system problem with some sounds of electrical problems as well. Adding the product Heet, or the newer Iso-Heet to your cars gas tank is MORE expensive than going to the pharmacy and buying a bottle of 91-100% Isopropal alcohol and adding that to you gas tank! That's what's really in both Hewet products. The alcohol bonds with the… [cont.]
Answered by mangamaniaciam - Sat Mar 17 13:19:43 2007
Q. will a simple cup of water casue rough running or stalling or does it take more water to cause my problems? very curious. thanks
Asked by lucky - Sat Mar 17 13:08:04 2007 - - 3 Answers - 0 Comments
A. Water in the gas tank and lines is very common. More so than most people think it is. To help you out here, if you had a two gallon glass container with a gallon of gas in it(doesn't matter what grade), to make it run poorly, you'd have to add about another quart if not nearly a half gallon of water to the gasoline to make it really bad. Rough idling at stop lights/signs as well as stalling is an ignition system problem with some sounds of electrical problems as well. Adding the product Heet, or the newer Iso-Heet to your cars gas tank is MORE expensive than going to the pharmacy and buying a bottle of 91-100% Isopropal alcohol and adding that to you gas tank! That's what's really in both Hewet products. The alcohol bonds with the… [cont.]
Answered by mangamaniaciam - Sat Mar 17 13:19:43 2007
do i need to remove the gas tank in my 2000 dodge caravan to replace the gas filter?
Q. do i need to remove the gas tank in my 2000 dodge caravan to replace the gas filter?
Asked by blake - Fri Jun 8 02:13:35 2007 - - 4 Answers - 0 Comments
A. no, it will be under you car towards the front, on the frame, looks a little smaller then a coke can, one fuel line going into it, and one coming out. each line will be held on with a nut. go to autozone and buy a filter for $9, then you will know what it looks like. slide under your van looking at the inside of the passenger frame rail and you will say "duh, there it is! that's easy!"
Answered by NotThe12th-Imam - Fri Jun 8 02:21:07 2007
Q. do i need to remove the gas tank in my 2000 dodge caravan to replace the gas filter?
Asked by blake - Fri Jun 8 02:13:35 2007 - - 4 Answers - 0 Comments
A. no, it will be under you car towards the front, on the frame, looks a little smaller then a coke can, one fuel line going into it, and one coming out. each line will be held on with a nut. go to autozone and buy a filter for $9, then you will know what it looks like. slide under your van looking at the inside of the passenger frame rail and you will say "duh, there it is! that's easy!"
Answered by NotThe12th-Imam - Fri Jun 8 02:21:07 2007
What is the best way to remove fumes from a gas tank to prepare for welding?
Q. Home Remidies would be best.
Asked by John G - Thu Mar 6 17:57:06 2008 - - 10 Answers - 0 Comments
A. wash the tank out,,then throw some dry ice in it.
Answered by alvarz - Thu Mar 6 18:00:26 2008
Q. Home Remidies would be best.
Asked by John G - Thu Mar 6 17:57:06 2008 - - 10 Answers - 0 Comments
A. wash the tank out,,then throw some dry ice in it.
Answered by alvarz - Thu Mar 6 18:00:26 2008
Can you remove gas from a 2004 C230 mercedes gas tank?
Q. Can you remove gas from a 2004 C230 mercedes gas tank?
Asked by Janet R - Fri Sep 21 19:55:47 2007 - - 3 Answers - 0 Comments
A. Yes, it is a saddle type tank, it goes over the drive shaft tunnel, there is a plug on the bottom of each half that needs to be removed.
Answered by CR - Fri Sep 21 21:23:09 2007
Q. Can you remove gas from a 2004 C230 mercedes gas tank?
Asked by Janet R - Fri Sep 21 19:55:47 2007 - - 3 Answers - 0 Comments
A. Yes, it is a saddle type tank, it goes over the drive shaft tunnel, there is a plug on the bottom of each half that needs to be removed.
Answered by CR - Fri Sep 21 21:23:09 2007
From Yahoo Answer Search: 'how do i remove a gas tank'
Wed Nov 18 15:35:53 2009 [ refresh local cache ]
[Hide]▼
fz6-forum.com
AdamDJ
Fri, 04 Sep 2009 07:00:00 GM
Well my new / 95% mint . tank. just arrived today.. It is black ( my fav color ) and in near mint condition.. Just has a couple light scratches and a.
[Hide]▲
